Chauvin Arnoux CA773 Voltage Absence Tester P01191773

Voltage Absence Testing: a clearly-defined procedure

In the context of work on installations connected to the electricity distribution network, the standards stipulate that the measurements must be performed with the power off to avoid electrical hazards (EN 50110-1 standard, DIN VDE 0682-401, NF C 18-510, etc.). To secure the installation and ensure that it is non-current-carrying, there is a procedure called Separation which imposes the use of a Voltage Absence Tester.

The C.A 773's comprehensive Autotest checks the electrical circuits, the power supply, the displays and the condition of the measurement leads. Audible and visual continuity testing is provided in compliance with Appendix B of the standard. The tester can also detect stray voltages and offers unipolar phase identification

All indoor and outdoor low-voltage applications

CAT IV 1,000 V Voltage Absence Testers (VATs) Use in extreme conditions: type-N extended climatic class RCD trip testing Digital display Complete integrated Autotest Extended continuity test (R< 0.5 Ω to 2.999 kΩ) Two-pole phase-sequence testing with "2-wire method" up to 400 Hz, suitable for isolating transformers and electrical generator sets

CA 773 & CA 771: beyond the standard recommendations

• A comprehensive integrated autotest with indication of the type of fault. The CA773 also displays a text message for complete information.
• The CA 773 & CA 771 VATs benefit from IP65 protection for indoor and outdoor use, which is significantly higher than the IP54 rating required by the standard.
• Extended class: for extreme environments, the CA 773 can be used for measurements from -15 °C to +45 °C (Class N).
• Audible and visual continuity indication up to 100 Ω, in compliance with the recommendation in Appendix B of the standard.
• The test probes are removable to meet specific requirements or to comply with the legislation in certain countries. Various models are available, including IP2X versions. Various models are available, including IP2X versions (required by the EN 61243 standard, for example).
• The CA 773 has significant measurement ranges and capabilities over it's counterpart CA 771, for a full breakdown please see the table below.

The Chauvin Arnoux CA 771 is available here.

Single-pole phase detection

You can detect the phase simply by establishing contact with one of the test probes

2-wire phase rotation with microprocessor

Simple and quick, the 2-wire phase rotation function with microprocessor is useful in all circumstances, including on installations powered by an electrical generator set or behind an isolating transformer.

Continuity and resistance testing

By pressing the continuity button, you can check that the conductors are correctly connected. Continuity (R < 100 Ω) is indicated by a loud, continuous audio signal. In addition, the CA 773 offers an extended continuity test and can be used to display the higher values from 0.5 Ω to 2.999 kΩ. The CA 773 displays the resistance value directly.

Residual Current Device (RCD) trip test up to 30 mA

By simultaneously pressing the double command, you can cause a fault current sufficient to trip the RCD to flow through a low-impedance load.

Applications:

Voltage up to 1,000 Vac / 1,400 Vdc at up to 800 Hz

The specifications of the CA 771 and CA 773 mean they can be used for work on all LV electrical networks, whether they are electricity distribution networks or the more specific networks encountered in naval or aviation applications.

The CA773 Comes Supplied With:

• 1 operating manual in 5 languages
• 2 x 1.5 V LR06/AA batteries
• 1 set of IP2X removable test probes
• 1 Velcro strap.
  
  

Climatic Conditions

The type-S extended climatic class allows use in extreme temperature conditions. This means it offers an operating range from -15 °C to +45 °C (Class N) for applications such as:

• Installations at altitude (mountains, etc.), underground installations, etc.
• Refrigeration installations, greenhouses, etc.,
• Service vehicles (emergency, army, etc.)
• The IP65 protection rating also ensures maximum protection against solid pollutants (dust) and liquid pollutants (projections), allowing both indoor and outdoor use.

Ergonomics specially designed for use in the field

• Digital display (CA 773) with text
• 2 moulded test probes to ensure excellent handling while protecting against falls and shocks
• Built-in torch to light the point of measurement
• Removable test probes and 2 positions provided on the VAT for 16 or 19 mm spacing
  
  

Spares & Accessories (Not Included):

The CA 753 measurement adapter can be used for measurements in total safety on European 2P+E and Schuko sockets.
Its design guarantees mechanical and electrical contact with all test probes (Ø 2 mm, Ø 4 mm, IP2x, etc.). The presence of a voltage (> 200 V) and the phase position are also indicated.

Removable accessories according to the requirements

Isolated test probes 2 or 4 mm in diameter, IP2X tip protection and test probes.

• CAT IV test probes for VATs P01102123Z
• Test probes Ø 2 mm for VATs P01102124Z
• Test probes Ø 4 mm for VATs P01102125Z
• Probe-tip protection for VATs P01102126Z
• CAT IV IP2X probes for VATs P01102127Z
• IP2X Ø 4 mm probes for VATs P01102128Z
• MultiFix bag, 120 x 320 x 60 mm P01298076
• CA 753 measurement adapter for European 2P+E sockets P01191748Z